Aqua-pure AP-RO5500 Installationshandbuch PDF herunterladen (Seite 11)

Installation, Operation and Maintenance Manual

11. Install the RO Assembly and Storage Tank

Under counter Installation:

The RO assembly is usually mounted to the right or left sink cabinet sidewall, taking into consideration the

space available and the tank location. Generally, the tank is placed in the rear of the sink cabinet while the

RO assembly is positioned toward the front for better accessibility.

TomounttheROassembly,elevateitatleast2”offthecabinetoor(withcartridgesinstalled)and,while

keepinglevel,markthelocationofthemountingholesonthecabinetsidewall.Makesmallpilotholeswith

an awl or drill and screw in the two mounting screws, leaving just enough protruding to allow bracket mount-

ing slots to slide over them.

NOTE:Ifthecabinetsidewallsarenotofsolidconstruction,theROassemblycanbesetonthecabinet

oorandheldagainstthesidewallwiththemountingscrews.However,theROassemblywillthenneedto

be lifted from the mounting screws in order to remove ﬁlter cartridges.

The tank can be oriented either vertically or horizontally. It is generally placed to the rear of the cabinet but

canbesetinthefromcenter(betweenthesinkbasins)foreaseofaccessifspacepermits.

Basement Installation:

TheROassemblyisgenerallymountedtothebasementwall(usingwallanchors)ortowoodceilingsup-

ports. To mount the RO assembly, keep bracket level and mark the location of the mounting holes. Install

wall anchors and/or mounting screws as required. Leave screw heads protruding to allow bracket mounting

slots to slide over them.

Thetankmaybeorientedeitherverticallyorhorizontallyandcanbeplacedonashelf,ontheoor,orsus-

pended from the ceiling supports using sturdy brackets.

An effort should be made to minimize the distance between the tank and RO assembly to help assure an

adequateowratetothefaucet.

12. Make Final Tubing Connections (see Figure 1)

With all of the components in place, the ﬁnal tubing connections can be made. When routing tubing be-

tween components, several guidelines should be observed.

Tubing runs should generally follow the contour of the cabinets rather than interfere with the cabinet stor-

agearea.Striveforneatnessandanorderlytubing“ow”usingfasteners(e.g.insulatedstaples)tosecure

thetubing.Arrangethetubingsotherearenosharpbendsandleavesome“play”inthetubingforeaseof

servicing, then cut tubing to desired length.

TrytokeepthetubingfromtheROassemblytothetankandfaucetasshortaspracticalforgoodow.

Undersink Installation:

A)Connectorange1/4”tubingfromfeedwatervalveto“Feed”connectiononROassembly.

B)Connectoneendofblue3/8”tubingtofaucetadapterandtheotherendtothe“faucet”connectionon

the RO assembly.

C)Connectyellow3/8”tubingfromstoragetanktotheteeontheROassembly.

D)Routespecialred“SFC”tubefromROassemblymodule(factorymadeconnection)towardfaucet.Do

not cut this special SFC tube. Its length is important to maintain proper efﬁciency and performance.

E)RemovewhiteplugfromcouplingttingonendofredSFCtube.ConnectSFCtubetooneendof1/4”

x1/4”couplingtting.

F) Connectthegreen1/4”tubingfromfaucetairgapto1/4”couplingttingontheendofSFCtube

(SeeFigure4onpage17).

To reduce the risk associated with a hazardous voltage due to an installer drilling through existing electric

wiring or water pipes in the area of installation:

 •Do not install near electric wiring or piping which may be in the path of a drilling tool when selecting the position

to mount the ﬁlter bracket.

WARNING

1 2 ... 6 7 8 9 10 11 12 13 14 15 16 ... 19 20

Kommentare zu diesen Handbüchern

Keine Kommentare

Aqua-pure AP-RO5500 Installationshandbuch Seite 11

Kommentare zu diesen Handbüchern